Beginning of this page.
Jump to main content.

Please note that JavaScript and style sheet are used in this website,
Due to unadaptability of the style sheet with the browser used in your computer, pages may not look as original.
Even in such a case, however, the contents can be used safely.

NEC NEC Display Solutions, Ltd.
Site menu starts here.
Skip site menu.
End of site menu.
Displaying present location in the site.
Home > Download > Software & Driver > MT1065 / MT1060 Update Software
End of menu.

MT1065 / MT1060 Update Software

Introduction of the Software

The MT1065 / MT1060 Update Software (hereafter, " Software " ) will update your firmware and setting data with the following features.

Firmware Ver. 1.15
Setting data Ver. 1.10

Changed Items

    in Ver. 1.14
  • Additional support Device.
    Device Model Note
    USB
    Memory
    CruzerMini 256MB no
    CruzerMini 128MB no
    PenDrive no
    Wireless LAN AmbiCom WL1100C Please use for over 5 degrees C around the PJ.
    D-Link DCF-660W no
    NETGEAR MA701 no
    in Ver. 1.09
  • Auto 3D Reform
  • Keystone Correction at Zoomed Lens Position
  • Using a USB Mouse
    • Selectable Mouse Pointer Icon
    • Middle button on the mouse support
  • USB Memory Device or USB Memory Card Reader Support
  • Display Version Information
  • More information is described in the supplementary document
    * In this supplementary document the name of MT860 is described, but this update software does not function on MT860.

CAUTION

Improper updating procedures can result in the projector not turning on.
Read this document carefully and avoid improper updating.
Should a power failure, lightning, accidental shutdown or noise occur during writing of data, the projector may fail to function normally.
In the worst case, this can lead to damage to the equipment. In this case, NEC Display Solutions shall not be liable for such damage and the user may be required to ask for repair at his / her own expense.

Target user

User that has either one of the following models.
MT1065 / MT1060

Updating

Be sure to read the following notes before updating.

NOTE

  • Update the firmware only once. After updating once, you do not need to do it again even if you unplug the projector.
  • Once updating is done, you cannot return to the previous version of the Software.
  • Once updating is done, other setting data than pertinent to the Security function and Logo are reset.

Preparation

  1. PC card --- 1 card
    • PC card compatible with the projector's PC card slot
      (For information about compatible PC cards that work with the projector,visit our projector web site: http://www.sharp-nec-displays.com/ap/ and see the page featuring the MT1065 / MT1060 projector.)
    • PC card with DOS FAT 16 file system
      (To format a PC card as DOS FAT 16 file system, see the user guide for the operating system on your computer.)
    • 8MB or more of free space
  2. Windows 98 / Me / 2000 / XP-compatible PC capable of reading and writing the above PC card --- 1 unit

Top of this page

Procedure for Updating

Follow the instructions below.
Preparation for updating the Software Updating the Firmware Updating the Setting Data

1. Preparation for updating the Software

1-1. Checking the file
Locate the file mt60v115e.exe and place it in a temporary folder.
For example: mt60v115e.exe is saved or moved to the C:¥TEMP folder.
1-2. Insert a PC card
Insert the PC card you prepared into the PC card drive in your PC.
1-3. Decompressing
  1. Locate and open C:¥TEMP folder.
  2. Double-click the mt60v115e.exe software in the C:¥TEMP folder.
  3. When the " Select Target Folder " window appears, click " Browse " and select the PC card drive.
  4. Next, click " Decompress " .
1-4. Verifying
Double-click the My Computer icon and then the PC card drive icon for verifying.
You should see two directories "_pjfirm! " and "_pjdat! " each containing a file " mt60v115.bin " and " mt60dldat_v110.bin " file respectively.
The extension for each of one of the files should be ".bin" .
Do not change the file name or extension.
CAUTION
Do not place other files than mt60v115.bin in the "_pjfirm! " folder.
Do not place other files than mt60dldat_v110.bin in the "_pjdat! " folder.
If there are two or more copies of the file, update will not be completed.

Top of this page

2. Updating the Firmware

2-1. Preparing the Projector
  1. Prepare a projector.
  2. Press the Main Power switch to the off position (O).
  3. Next, insert the PC card mentioned above into the PC card slot of the projector.
CAUTION
The MT1065 / MT1060 has two PC card slots, but only the slot 1 (upper) can be used for updating.
2-2. Starting updating
Follow the instructions below to start updating.
Perform the following steps 1 to 3 within 5 seconds.
  1. While pressing and holding the CANCEL button on the cabinet, press the Main Power switch to the on position (I).
    The STATUS indicator lights green. The POWER indicator does not light up at this moment. Do not release the CANCEL button at this moment.
  2. Release the CANCEL button and press it again. The STATUS indicator lights off and then lights green. The POWER indicator does not light up at this moment.
  3. Release the CANCEL button and then press the SELECT up button. After the STATUS indicator lights off, the POWER indicator lights orange and turns to green.
Updating has begun. Release the SELECT up button.
The PC CARD indicator lights green during processing.

Updating takes 3 to 4 minutes.
It could take longer than the above time depending on the format of a PC card.
When the POWER indicator turns to orange, updating is complete.

Conditions other than above, such as flashing red indicates updating is not complete.
Should this happen, start from the beginning again.
2-3. Restarting
After the update is finished, press the projector Main Power switch to the off position (O) and wait for all indicator LEDs to go off.
Press the Main Power switch to the on position (I) again to start up the updated firmware.
2-4. Confirming the version
Verify that the firmware has been rewritten.
  1. Press and hold the ON / STANDBY button on the projector for a minimum of 2 seconds to turn on the projector.
  2. Press the MENU button on the projector.
  3. Select " Help " → " Information " and press the ENTER button.
  4. Select " Page 4 " and check to see if " Firmware " is Ver. 1.15.
    If " Firmware " is not Ver. 1.15, start from the beginning again.
This completes updating the firmware.

Top of this page

3. Updating the Setting Data

3-1. Preparing the Projector
  1. Prepare a projector.
  2. Press the Main Power switch to the off position (O).
  3. Next, insert the PC card mentioned above into the PC card slot of the projector if it is not already in the PC card slot.
CAUTION
The MT1065 / MT1060 has two PC card slots, but only the slot 1 (upper) can be used for updating.
3-2. Starting updating
Follow the instructions below to start updating.
Perform the following steps 1 to 3 within 5 seconds.
  1. While pressing and holding the CANCEL button on the cabinet, press the Main Power switch to the on position (I).
    The STATUS indicator lights green. The POWER indicator does not light up at this moment. Do not release the CANCEL button at this moment.
  2. Release the CANCEL button and press it again.The STATUS indicator lights off and then lights green. The POWER indicator does not light up at this moment.
  3. Release the CANCEL button and then press the MENU button.After the STATUS indicator lights off, the POWER indicator lights green.
Updating has begun. Release the MENU button.
The PC CARD indicator flashes to green periodically.

Updating takes 30 to 60 seconds.
It could take longer than the above time depending on the format of a PC card.
When the POWER indicator turns to orange, updating is complete.

Conditions other than above, such as flashing red indicates updating is not complete.
Should this happen, start from the beginning again.
3-3. Restarting
After the update is finished, press the projector Main Power switch to the off position (O) and wait for all indicator LEDs to go off.
Press the Main Power switch to the on position (I) again to start up the firmware using updated setting data.
3-4. Confirming the version
Verify that the setting data has been rewritten.
  1. Press and hold the ON / STANDBY button on the projector for a minimum of 2 seconds to turn on the projector.
  2. Press the MENU button on the projector.
  3. Select " Help " → " Information " and press the ENTER button.
  4. Select " Page 4 " and check to see if " Data " is Ver1.10.
    If " Data " is not Ver1.10, start from the beginning again.
This completes updating the setting data.

Go to download

Choose a filename from the following list.
download file file name file size
MT1065 / MT1060 Update Software:
Firmware Ver. 1.15
mt60v115e.exe EXE 1.38MB
MT1075 / MT1065 User's Manual Suppliment (for Ver. 1.15)
(English / Deutsch / Francais / Italiano / Espanol / Svenska)
MT1075SUPPLEMENT.pdf PDF 96KB
User's Manual Suppliment
(for Ver. 1.09)
(English/ Deutsch/ Francais/ Italiano/ Espanol/ Svenska)
mt60sup.pdf PDF 1.35MB

Top of this page

Copyright NEC Display Solutions, Ltd. All rights reserved.